[Command] Terminate flight immediately. Flight termination immediately and irreversably terminates the current flight, returning the vehicle to ground. The vehicle will ignore RC or other input until it has been power-cycled. Termination may trigger safety measures, including: disabling motors and deployment of parachute on multicopters, and setting flight surfaces to initiate a landing pattern on fixed-wing). On multicopters without a parachute it may trigger a crash landing. Support for this command can be tested using the protocol bit: MAV_PROTOCOL_CAPABILITY_FLIGHT_TERMINATION. Support for this command can also be tested by sending the command with param1=0 (
Iso Commander V1 6 043 Incl Serial
[Command] Set the mission item with sequence number seq as the current item and emit MISSION_CURRENT (whether or not the mission number changed). If a mission is currently being executed, the system will continue to this new mission item on the shortest path, skipping any intermediate mission items. Note that mission jump repeat counters are not reset unless param2 is set (see MAV_CMD_DO_JUMP param2). This command may trigger a mission state-machine change on some systems: for example from MISSION_STATE_NOT_STARTED or MISSION_STATE_PAUSED to MISSION_STATE_ACTIVE. If the system is in mission mode, on those systems this command might therefore start, restart or resume the mission. If the system is not in mission mode this command must not trigger a switch to mission mode. The mission may be "reset" using param2. Resetting sets jump counters to initial values (to reset counters without changing the current mission item set the param1 to `-1`). Resetting also explicitly changes a mission state of MISSION_STATE_COMPLETE to MISSION_STATE_PAUSED or MISSION_STATE_ACTIVE, potentially allowing it to resume when it is (next) in a mission mode. The command will ACK with MAV_RESULT_FAILED if the sequence number is out of range (including if there is no mission item).
[Message] A ping message either requesting or responding to a ping. This allows to measure the system latencies, including serial port, radio modem and UDP connections. The ping microservice is documented at
[Message] Emit the value of a onboard parameter. The inclusion of param_count and param_index in the message allows the recipient to keep track of received parameters and allows him to re-request missing parameters after a loss or timeout. The parameter microservice is documented at
[Message] Control a serial port. This can be used for raw access to an onboard serial peripheral such as a GPS or telemetry radio. It is designed to make it possible to update the devices firmware via MAVLink messages or change the devices settings. A message with zero bytes can be used to change just the baudrate.
[Message] Estimator status message including flags, innovation test ratios and estimated accuracies. The flags message is an integer bitmask containing information on which EKF outputs are valid. See the ESTIMATOR_STATUS_FLAGS enum definition for further information. The innovation test ratios show the magnitude of the sensor innovation divided by the innovation check threshold. Under normal operation the innovation test ratios should be below 0.5 with occasional values up to 1.0. Values greater than 1.0 should be rare under normal operation and indicate that a measurement has been rejected by the filter. The user should be notified if an innovation test ratio greater than 1.0 is recorded. Notifications for values in the range between 0.5 and 1.0 should be optional and controllable by the user.
[Message] (MAVLink 2) Emit the value of a parameter. The inclusion of param_count and param_index in the message allows the recipient to keep track of received parameters and allows them to re-request missing parameters after a loss or timeout.
[Message] (MAVLink 2) Data for filling the OpenDroneID System message. The System Message contains general system information including the operator location/altitude and possible aircraft group and/or category/class information.
The configuration data is passed as a parameter to the start address of the new thread. This data includes the encrypted configuration settings for Brute Ratel C4. The encrypted contents are the following:
Palo Alto Networks has shared these findings, including file samples and indicators of compromise, with our fellow Cyber Threat Alliance members. CTA members use this intelligence to rapidly deploy protections to their customers and to systematically disrupt malicious cyber actors. Learn more about the Cyber Threat Alliance. 2ff7e9595c
Comments